Floppy disk

2008/9 Schools Wikipedia Selection. Related subjects: Computing hardware and infrastructure

Floppy Disk Drive

8-inch, 5¼-inch (full height), and 3½-inch drives
Date Invented: 1969 (8-inch),
1976 (5¼-inch),
1984 (3½-inch)
Invented By: IBM team led by David Noble
Connects to:
  • Controller via cable

A floppy disk is a data storage medium that is composed of a disk of thin, flexible ("floppy") magnetic storage medium encased in a square or rectangular plastic shell. Floppy disks are read and written by a floppy disk drive or FDD, the initials of which should not be confused with "fixed disk drive", which is another term for a hard disk drive. Invented by IBM, floppy disks in 8-inch (200 mm), 5¼-inch (133⅓ mm), and the newest and most common 3½-inch (90 mm) formats enjoyed many years as a popular and ubiquitous form of data storage and exchange, from the mid-1970s to the late 1990s. They have now been superseded by flash and optical storage devices.

Recent usage

The flexible magnetic disk, or diskette (-ette is a diminutive suffix), revolutionized computer disk storage in the 1970s. Diskettes, which were often called floppy disks or floppies by English speaking users, became ubiquitous in the 1980s and 1990s in their use with personal computers and home computers, such as the Apple II, Macintosh, Commodore 64, Atari ST, and Amiga, to distribute software, transfer data, and create backups.

Before hard disks became affordable, floppy disks were often also used to store a computer's operating system (OS), in addition to application software and data. Most home computers had a primary OS (often BASIC) stored permanently in on-board ROM, with the option of loading a more advanced disk operating system from a floppy, whether it be a proprietary system, CP/M, or later, DOS.

By the early 1990s, the increasing size of software meant that many programs demanded multiple diskettes; a large package like Windows or Adobe Photoshop could use a dozen disks or more. Toward the end of the 1990s, distribution of larger packages therefore gradually switched to CD-ROM (or online distribution for smaller programs).

Mechanically incompatible higher-density formats were introduced (e.g. the Iomega Zip disk) and were briefly popular, but adoption was limited by the competition between proprietary formats, and the need to buy expensive drives for computers where the media would be used. In some cases, such as with the Zip drive, the failure in market penetration was exacerbated by the release of newer higher-capacity versions of the drive and media that were not forward-compatible with the original drives, thus fragmenting the user base between new users and early adopters who were unwilling to pay for an upgrade so soon. A chicken or the egg scenario ensued, with consumers wary of making costly investments into unproven and rapidly changing technologies, with the result that none of the technologies were able to prove themselves and stabilize their market presence. Soon, inexpensive recordable CDs with even greater capacity, which were also compatible with an existing infrastructure of CD-ROM drives, made the new floppy technologies redundant. The last advantage of floppy disks, reusability, was again countered by re-writable CDs. Later, advancements in flash-based devices and widespread adoption of the USB interface provided another alternative that, in turn, made even optical storage obsolete for some purposes.

An attempt to continue the traditional diskette was the SuperDisk (LS-120) in the late 1990s, with a capacity of 120 MB (actually 120.375 MiB), which was backward compatible with standard 3½-inch floppies. For some time, PC manufacturers were reluctant to remove the floppy drive because many IT departments appreciated a built-in file transfer mechanism that always worked and required no device driver to operate properly. However, manufacturers and retailers have progressively reduced the availability of computers fitted with floppy drives and of the disks themselves.

External USB-based floppy disk drives are available for computers without floppy drives, and they work on any machine that supports USB Mass Storage Devices. Many modern systems even provide firmware support for booting to a USB-mounted floppy drive.

It should be noted that Windows XP still requires the use of floppy drives to install third-party RAID, SATA and AHCI hard drives. This requirement was only dropped with the introduction of Windows Vista in 2007. To this day (12/08/2008), most PC motherboards will still attempt to boot from a floppy drive, depending on CMOS settings.

Disk formats

Floppy disk sizes are almost universally referred to in imperial measurements, even in countries where metric is the standard, and even when the size is in fact defined in metric (for instance the 3½-inch floppy, which is actually 90 mm). Formatted capacities are generally set in terms of binary kilobytes (as 1 sector is generally 512 bytes). For more information see below.

Historical sequence of floppy disk formats, including the last format to be generally adopted — the "High Density" 3½-inch HD floppy, introduced 1987.
Disk format Year introduced Formatted
Storage capacity
(in kB = 1024 bytes if not stated)
8-inch - IBM 23FD (read-only) 1971 79.7 ?
8-inch - Memorex 650 1972 175 kB 1.5 megabit [unformatted]
8-inch - SSSD

IBM 33FD / Shugart 901

1973 237.25 3.1 Mbits unformatted
8-inch - DSSD

IBM 43FD / Shugart 850

1976 500.5 6.2 Mbits unformatted
5¼-inch (35 track)

Shugart SA 400

1976 89.6 kB 110 kB
8-inch DSDD

IBM 53FD / Shugart 850

1977 980 ( CP/M)
- 1200 ( MS-DOS FAT)
1.2 MB
5¼-inch DD 1978 360 or 800 360 KB
HP single sided
1982 280 264 kB
3-inch 1982 360 ?
3½-inch (DD at release) 1984 720 720 KB
5¼-inch QD 720 720 KB
5¼-inch HD 1982 YE Data YD380 1,182,720 bytes 1.2 MB
3-inch DD 1984 720 ?
Mitsumi Quick Disk
1985 128 to 256 ?
2-inch 1985 720 ?
5¼-inch Perpendicular 1986 100 MB ?
3½-inch HD 1987 1440 1.44 MB
3½-inch ED 1987 2880 2.88 MB
3½-inch Floptical (LS) 1991 21000 21 MB
3½-inch LS-120 1996 120.375 MB 120 MB
3½-inch LS-240 1997 240.75 MB 240 MB
3½-inch HiFD 1998/99 150/200 MB 150/200 MB
Abbreviations: DD = Double Density; QD = Quad Density; HD = High Density; ED = Extended Density; LS = Laser Servo; HiFD = High capacity Floppy Disk; SS = Single Sided; DS = Double Sided
¹ The formatted capacities of floppy disks frequently corresponded only vaguely to their capacities as marketed by drive and media companies, due to differences between formatted and unformatted capacities and also due to the non-standard use of binary prefixes in labeling and advertising floppy media. The erroneous "1.44 MB" value for the 3½-inch HD floppies is the most widely known example. See reported storage capacity.
Dates and capacities marked ? are of unclear origin and need source information; other listed capacities refer to:

Formatted Storage Capacity is total size of all sectors on the disk:

  • For 8-inch see Table of 8-inch floppy formats IBM 8-inch formats. Note that spare, hidden and otherwise reserved sectors are included in this number.
  • For 5¼- and 3½-inch capacities quoted are from subsystem or system vendor statements.

Marketed Capacity is the capacity, typically unformatted, by the original media OEM vendor or in the case of IBM media, the first OEM thereafter. Other formats may get more or less capacity from the same drives and disks.


8-inch disk drive with diskette (3½" disk for comparison)
8-inch disk drive with diskette (3½" disk for comparison)

The earliest floppy disks, invented at IBM, were 8 inches in diameter. They became commercially available in 1971. Disks in this form factor were produced and improved upon by IBM and other companies such as Memorex, Shugart Associates, and Burroughs Corporation.

A double-density 5¼-inch disk.
A double-density 5¼-inch disk.

In 1976 two of Shugart Associates’s employees, Jim Adkisson and Don Massaro, were approached by An Wang of Wang Laboratories, who felt that the 8-inch format was simply too large for the desktop word processing machines he was developing at the time. After meeting in a bar in Boston, Adkisson asked Wang what size he thought the disks should be, and Wang pointed to a napkin and said “about that size”. Adkisson and Massaro took the napkin back to California, found it to be 5¼ inches wide, and developed a new drive of this size storing 98.5 KB later increased to 110 KB by adding 5 tracks. The 5¼-inch drive was considerably less expensive than 8-inch drives from IBM, and soon started appearing on CP/M machines. At one point Shugart was producing 4,000 drives a day. By 1978 there were more than 10 manufacturers producing 5¼-inch floppy drives, in competing physical disk formats: hard-sectored (90 KB) and soft-sectored (110 KB). The 5¼-inch formats quickly displaced the 8-inch for most applications, and the 5¼-inch hard-sectored disk format eventually disappeared.

Throughout the early 1980s the limitations of the 5¼-inch format were starting to become clear. Originally designed to be smaller and more practical than the 8-inch format, the 5¼-inch system was itself too large, and as the quality of the recording media grew, the same amount of data could be placed on a smaller surface. Another problem was that the 5¼-inch disks were simply scaled down versions of the 8-inch disks, which had never really been engineered for ease of use. The thin folded-plastic shell allowed the disk to be easily damaged through bending, and allowed dirt to get onto the disk surface through the opening.

A number of solutions were developed, with drives at 2-inch, 2½-inch, 3-inch and 3½-inch (50, 60, 75 and 90 mm) all being offered by various companies. They all shared a number of advantages over the older format, including a small form factor and a rigid case with a slideable write protect catch. The almost-universal use of the 5¼-inch format made it very difficult for any of these new formats to gain any significant market share.

Standard 3½ with a blank label
Standard 3½ with a blank label

Sony introduced their own small-format 90.0 mm × 94.0 mm disk, similar to the others but somewhat simpler in construction than the AmDisk. The first computer to use this format was Sony's SMC 70 of 1982. Other than Hewlett-Packard's HP-150 of 1983 and Sony's MSX computers that year, this format suffered from a similar fate as the other new formats: the 5¼-inch format simply had too much market share. Things changed dramatically when several companies started adopting the format. In 1984 Apple Computer selected the format for their new Macintosh computers, in 1985 Atari for their new ST line and Commodore for their new Amiga. By 1988 the 3½-inch was outselling the 5¼-inch.

By the end of the 1980s, the 5¼-inch disks had been superseded by the 3½-inch disks. Though 5¼-inch drives were still available, as were disks, they faded in popularity as the 1990s began. The main community of users was primarily those who still owned '80s legacy machines (PCs running MS-DOS or home computers) that had no 3½-inch drive; the advent of Windows 95 (not even sold in stores in a 5¼-inch version; a coupon had to be obtained and mailed in) and subsequent phaseout of standalone MS-DOS with version 6.22 forced many of them to upgrade their hardware. On most new computers the 5¼-inch drives were optional equipment. By the mid-1990s the drives had virtually disappeared as the 3½-inch disk became the predominant floppy disk.

Floppy replacements

Through the early 1990s a number of attempts were made by various companies to introduce newer floppy-like formats based on the now-universal 3½-inch physical format. Most of these systems provided the ability to read and write standard DD and HD disks, while at the same time introducing a much higher-capacity format as well. There were a number of times where it was felt that the existing floppy was just about to be replaced by one of these newer devices, but a variety of problems ensured this never took place. None of these ever reached the point where it could be assumed that every current PC would have one, and they have now largely been replaced by CD and DVD burners and USB flash drives.

The main technological change was the addition of tracking information on the disk surface to allow the read/write heads to be positioned more accurately. Normal disks have no such information, so the drives use the tracks themselves with a feedback loop in order to centre themselves. The newer systems generally used marks burned onto the surface of the disk to find the tracks, allowing the track width to be greatly reduced.


As early as 1988, Brier Technology introduced the Flextra BR 3020, which boasted 21.4 MB (marketing, true size was 21,040 KiB, 25 MiB unformatted). Later the same year it introduced the BR3225, which doubled the capacity. This model could also read standard 3½-inch disks.

Apparently it used 3½-inch standard disks which had servo information embedded on them for use with the Twin Tier Tracking technology.


In 1991, Insite Peripherals introduced the " Floptical", which used an infra-red LED to position the heads over marks in the disk surface. The original drive stored 21 MB, while also reading and writing standard DD and HD floppies. In order to improve data transfer speeds and make the high-capacity drive usefully quick as well, the drives were attached to the system using a SCSI connector instead of the normal floppy controller. This made them appear to the operating system as a hard drive instead of a floppy, meaning that most PCs were unable to boot from them. This again adversely affected pickup rates.

Insite licenced their technology to a number of companies, who introduced compatible devices as well as even larger-capacity formats. Most popular of these, by far, was the LS-120, mentioned below.

Zip drive

In 1994, Iomega introduced the Zip drive. Not true to the 3½-inch form factor, hence not compatible with the standard 1.44 MB floppies (which may have actually been a good thing for the drives as it removed a big potential source of problems), it became the most popular of the "super floppies". It boasted 100 MB, later 250 MB, and then 750 MB of storage. Though Zip drives gained in popularity for several years they never reached the same market penetration as floppy drives as only some new computers were sold with the drives. Eventually the falling prices of CD-R and CD-RW media and flash drives, along with notorious hardware failures (the so-called " click of death"), reduced the popularity of the Zip drive.

A major reason for the failure of the Zip Drives is also attributed to the higher pricing they carried. However hardware vendors such as Hewlett Packard, Dell and Compaq had promoted the same at a very high level. Zip drive media were primarily popular for the excellent storage density and drive speed they carried, but were always overshadowed by the price.


Announced in 1995, the " SuperDisk" drive, often seen with the brand names Matsushita (Panasonic) and Imation, had an initial capacity of 120 MB (120.375 MiB) using even higher density "LS-120" disks.

It was upgraded ("LS-240") to 240 MB (240.75 MiB). Not only could the drive read and write 1440 kB disks, but the last versions of the drives could write 32 MB onto a normal 1440 kB disk (see note below). Unfortunately, popular opinion held the Super Disk disks to be quite unreliable, though no more so than the Zip drives and SyQuest Technology offerings of the same period and there were also many reported problems moving standard floppies between LS-120 drives and normal floppy drives. This belief, true or otherwise, crippled adoption. The BIOS of many motherboards even to this day supports LS-120 drives as boot options.

Sony HiFD

Sony introduced their own floptical-like system in 1997 as the "150 MB Sony HiFD" which could hold 150 megabytes (157.3 actual megabytes) of data. Although by this time the LS-120 had already garnered some market penetration, industry observers nevertheless confidently predicted the HiFD would be the real floppy-killer and finally replace floppies in all machines.

After only a short time on the market the product was pulled, as it was discovered there were a number of performance and reliability problems that made the system essentially unusable. Sony then re-engineered the device for a quick re-release, but then extended the delay well into 1998 instead, and increased the capacity to "200 MB" (approximately 210 megabytes) while they were at it. By this point the market was already saturated by the Zip disk, so it never gained much market share.

Caleb Technology’s UHD144

The UHD144 drive surfaced early in 1998 as the it drive, and provided 144 MB of storage while also being compatible with the standard 1.44 MB floppies. The drive was slower than its competitors but the media were cheaper, running about $8 at introduction and $5 soon after.


A user inserts the floppy disk, medium opening first, into a 5¼-inch floppy disk drive (pictured, an internal model) and moves the lever down (by twisting on this model) to close the drive and engage the motor and heads with the disk.
A user inserts the floppy disk, medium opening first, into a 5¼-inch floppy disk drive (pictured, an internal model) and moves the lever down (by twisting on this model) to close the drive and engage the motor and heads with the disk.

The 5¼-inch disk had a large circular hole in the centre for the spindle of the drive and a small oval aperture in both sides of the plastic to allow the heads of the drive to read and write the data. The magnetic medium could be spun by rotating it from the middle hole. A small notch on the right hand side of the disk would identify whether the disk was read-only or writable, detected by a mechanical switch or photo transistor above it. Another LED/phototransistor pair located near the centre of the disk could detect a small hole once per rotation, called the index hole, in the magnetic disk. It was used to detect the start of each track, and whether or not the disk rotated at the correct speed; some operating systems, such as Apple DOS, did not use index sync, and often the drives designed for such systems lacked the index hole sensor. Disks of this type were said to be soft sector disks. Very early 8-inch and 5¼-inch disks also had physical holes for each sector, and were termed hard sector disks. Inside the disk were two layers of fabric designed to reduce friction between the medium and the outer casing, with the medium sandwiched in the middle. The outer casing was usually a one-part sheet, folded double with flaps glued or spot-welded together. A catch was lowered into position in front of the drive to prevent the disk from emerging, as well as to raise or lower the spindle (and, in two-sided drives, the upper read/write head).

The 3½-inch disk is made of two pieces of rigid plastic, with the fabric-medium-fabric sandwich in the middle to remove dust and dirt. The front has only a label and a small aperture for reading and writing data, protected by a spring-loaded metal or plastic cover, which is pushed back on entry into the drive.

The 3½-inch floppy disk drive automatically engages when the user inserts a disk, and disengages and ejects with the press of the eject button. On Macintoshes with built-in floppy drives, the disk is ejected by a motor (similar to a VCR) instead of manually; there is no eject button. The disk's desktop icon is dragged onto the Trash icon to eject a disk.
The 3½-inch floppy disk drive automatically engages when the user inserts a disk, and disengages and ejects with the press of the eject button. On Macintoshes with built-in floppy drives, the disk is ejected by a motor (similar to a VCR) instead of manually; there is no eject button. The disk's desktop icon is dragged onto the Trash icon to eject a disk.

The reverse has a similar covered aperture, as well as a hole to allow the spindle to connect into a metal plate glued to the medium. Two holes, bottom left and right, indicate the write-protect status and high-density disk correspondingly, a hole meaning protected or high density, and a covered gap meaning write-enabled or low density. (Incidentally, the write-protect and high-density holes on a 3½-inch disk are spaced exactly as far apart as the holes in punched A4 paper (8 cm), allowing write-protected floppies to be clipped into European ring binders.) A notch top right ensures that the disk is inserted correctly, and an arrow top left indicates the direction of insertion. The drive usually has a button that, when pressed, will spring the disk out at varying degrees of force. Some would barely make it out of the disk drive; others would shoot out at a fairly high speed. In a majority of drives, the ejection force is provided by the spring that holds the cover shut, and therefore the ejection speed is dependent on this spring. In PC-type machines, a floppy disk can be inserted or ejected manually at any time (evoking an error message or even lost data in some cases), as the drive is not continuously monitored for status and so programs can make assumptions that do not match actual status (e.g., disk 123 is still in the drive and has not been altered by any other agency). With Apple Macintosh computers, disk drives are continuously monitored by the OS; a disk inserted is automatically searched for content and one is ejected only when the software agrees the disk should be ejected. This kind of disk drive (starting with the slim "Twiggy" drives of the late Apple "Lisa") does not have an eject button, but uses a motorized mechanism to eject disks; this action is triggered by the OS software (e.g. the user dragged the "drive" icon to the "trash can" icon). Should this not work (as in the case of a power failure or drive malfunction), one can insert a straightened paper clip into a small hole at the drive's front, thereby forcing the disk to eject (similar to that found on CD/DVD drives). Some other computer designs (such as the Commodore Amiga) monitor for a new disk continuously, but still have push-button eject mechanisms.

The 3-inch disk bears much similarity to the 3½-inch type, with some unique and somewhat curious features. One example is the rectangular-shaped plastic casing, almost taller than a 3½-inch disk, but narrower, and more than twice as thick, almost the size of a standard compact audio cassette. This made the disk look more like a greatly oversized present day memory card or a standard PC card notebook expansion card rather than a floppy disk. Despite the size, the actual 3-inch magnetic-coated disk occupied less than 50% of the space inside the casing, the rest being used by the complex protection and sealing mechanisms implemented on the disks. Such mechanisms were largely responsible for the thickness, length and high costs of the 3-inch disks. On the Amstrad machines the disks were typically flipped over to use both sides, as opposed to being truly double-sided. Double-sided mechanisms were available but rare.


An example of a modern USB floppy disk drive.
An example of a modern USB floppy disk drive.

The 8-inch, 5¼-inch and 3-inch formats can be considered almost completely obsolete, although 3½-inch drives and disks are still widely available. As of 2007 3½-inch drives are still available on many desktop PC systems, although it is usually now an optional extra or has to be bought and installed separately. Hewlett-Packard has recently dropped supplying floppy drives as standard on business desktops. The majority of ATX and Micro-ATX PC cases are still designed to accommodate at least one 3.5" drive that can be accessed from the front of the PC (although this bay can be used for other devices, such as flash memory readers). As of 2007, HD floppy disks are still quite commonly available in most computer and stationery shops, although selection is usually very limited.

The advent of other portable storage options, such as USB storage devices and recordable or rewritable CDs, and the rise of multi- megapixel digital photography has encouraged the creation and use of files larger than most 3½-inch disks can hold. In addition, the increasing availability of broadband and wireless Internet connections has decreased the utility of removable storage devices overall. The 3½-inch floppy is growing as obsolete as its larger cousin a decade before. However, the 3½-inch floppy has been in continuous use longer than the 5¼-inch floppy.

Floppies are still used for emergency boots in aging systems which may lack support for bootable media such as CD-ROMs and USB devices. They are also still often required for setting up a new PC from the ground up, since even comparatively recent operating systems like Windows XP and Windows Server 2003 rely on third party drivers shipped on floppies: for example, SATA support during installation. Only Windows Vista, using Windows PE, now allows drivers to be loaded from media other than floppies during installation. Floppies are also still often required for BIOS updates, and as maintenance program carriers, since many BIOS and firmware update/restore programs are still designed to be executed from a bootable floppy disk. Floppy drives are also used to access non-critical data that may still be on floppy disks, such as personal data or legacy games and software. As well, office workplaces have often disabled high volume writable media such as optical drivers and USB ports to prevent employees from taking large amounts of data, so the small capacity of the floppy limits the information compromised.

Apple, the first manufacturer to popularly include 3½-inch drives as standard equipment — on the Apple Macintosh in 1984 — was also the first manufacturer to not include them on new machines - in 1998 with the advent of the iMac. This made USB-connected floppy drives a popular accessory for the early iMacs, since the basic model of iMac at the time had only a CD-ROM drive, giving users no easy access to writable removable media. This transition away from floppies was easier for Apple, since all Macintosh models were able to boot and install their operating system from CD-ROM early on.

In February 2003, Dell, Inc. announced that they would no longer include floppy drives on their Dell Dimension home computers as standard equipment, although they are available as a selectable option for around $20 and can be purchased as an aftermarket OEM add-on anywhere between $5 and $25.

On 29 January 2007 the British computer retail chain PC World issued a statement saying that only 2% of the computers that they sold contained a built-in floppy disk drive and, once present stocks were exhausted, no more floppies would be sold.

The music industry still employs many types of electronic equipment that use floppy disks as a storage medium. Synthesizers, samplers, drum machines, and sequencers continue to use 3½-inch disks. Other storage options, such as CD-R, CD-RW, network connections, and USB storage devices have taken much longer to mature in this industry.


In general, different physical sizes of floppy disks are incompatible by definition, and disks can be loaded only on the correct size of drive. There were some drives available with both 3½-inch and 5¼-inch slots that were popular in the transition period between the sizes.

However, there are many more subtle incompatibilities within each form factor. For example, all but the earliest models of Apple Macintosh computers that have built-in floppy drives included a disk controller that can read, write and format IBM PC-format 3½-inch diskettes. However, few IBM-compatible computers use floppy disk drives that can read or write disks in Apple's variable speed format. For details on this, see the section More on floppy disk formats.

Within the world of IBM-compatible computers, the three densities of 3½-inch floppy disks are partially compatible. Higher density drives are built to read, write and even format lower density media without problems, provided the correct media are used for the density selected. However, if by whatever means a diskette is formatted at the wrong density, the result is a substantial risk of data loss due to magnetic mismatch between oxide and the drive head's writing attempts. Still, a fresh diskette that has been manufactured for high density use can theoretically be formatted as double density, but only if no information has ever been written on the disk using high density mode (for example, HD diskettes that are pre-formatted at the factory are out of the question). The magnetic strength of a high density record is stronger and will "overrule" the weaker lower density, remaining on the diskette and causing problems. However, in practice there are people who use downformatted (ED to HD, HD to DD) or even overformatted (DD to HD) without apparent problems. Doing so always constitutes a data risk, so one should weigh out the benefits (e.g. increased space and/or interoperability) versus the risks (data loss, permanent disk damage).

The 5¼-inch minifloppy

A square hole punch used for 5 1/4 floppy disks.
A square hole punch used for 5 1/4 floppy disks.

The holes on the right side of a 3½-inch disk can be altered as to 'fool' some disk drives or operating systems (others such as the Acorn Archimedes simply do not care about the holes) into treating the disk as a higher or lower density one, for backward compatibility or economical reasons. Possible modifications include:

  • Drilling or cutting an extra hole into the right-lower side of a 3½-inch DD disk (symmetrical to the write-protect hole) in order to format the DD disk into a HD one. This was a popular practice during the early 1990s, as most people switched to HD from DD during those days and some of them "converted" some or all of their DD disks into HD ones, for gaining an extra "free" 720 KiB of disk space. There even was a special hole punch that was made to easily make this extra (square) hole in a floppy.
  • Taping or otherwise covering the right hole on a HD 3½-inch disk enables it to be 'downgraded' to DD format. This may be done for reasons such as compatibility issues with older computers, drives or devices that use DD floppies, like some electronic keyboard instruments and samplers where a 'downgraded' disk can be useful, as factory-made DD disks have become hard to find after the mid-1990s. See the section "Compatibility" above.
    • Note: By default, many older HD drives will recognize ED disks as DD ones, since they lack the HD-specific holes and the drives lack the sensors to detect the ED-specific hole. Most DD drives will also handle ED (and some even HD) disks as DD ones.
  • Similarly, drilling an HD-like hole (under the ED one) into an ED (2880 kiB) disk for 'downgrading' it to HD (1440 kiB) format if there are many unusable ED disks due to the lack of a specific ED drive, which can now be used as normal HD disks.
  • Even if such a format was hardly officially supported on any system, it is possible to "force" a 3½-inch floppy disk drive to be recognized by the system as a 5¼-inch 360 kB or 1200 kB one (on PCs and compatibles, this can be done by simply changing the CMOS BIOS settings) and thus format and read non-standard disk formats, such as a double sided 360 kB 3½-inch disk. Possible applications include data exchange with obsolete CP/M systems, for example with an Amstrad CPC.

The situation was even more complex with 5¼-inch diskettes. The head gap of an 80 track (1200 kB in the PC world) drive is shorter than that of a 40 track (360 kB in the PC world) drive, but will format, read and write 40 track diskettes with apparent success provided the controller supports double stepping (or the manufacturer fitted a switch to do double stepping in hardware). A blank 40 track disk formatted and written on an 80 track drive can be taken to a 40 track drive without problems, similarly a disk formatted on a 40 track drive can be used on an 80 track drive. But a disk written on a 40 track drive and updated on an 80 track drive becomes permanently unreadable on any 360 kB drive, owing to the incompatibility of the track widths (special, very slow programs could have been used to overcome this problem). There are several other 'bad' scenarios.

Prior to the problems with head and track size, there was a period when just trying to figure out which side of a "single sided" diskette was the right side was a problem. Both Radio Shack and Apple used 360 kB single sided 5¼-inch disks, and both sold disks labeled "single sided" that were certified for use on only one side, even though they in fact were coated in magnetic material on both sides. The irony was that the disks would work on both Radio Shack and Apple machines, yet the Radio Shack TRS-80 Model I computers used one side and the Apple II machines used the other, regardless of whether there was software available which could make sense of the other format.

"Sub Battle Simulator" for the Tandy Color Computer 3 was released on a "flippy" disk
"Sub Battle Simulator" for the Tandy Colour Computer 3 was released on a "flippy" disk

For quite a while in the 1980s, users could purchase a special tool called a "disk notcher" which would allow them to cut a second "write unprotect" notch in these diskettes and thus use them as "flippies" (either inserted as intended or upside down): both sides could now be written on and thereby the data storage capacity was doubled. Other users made do with a steady hand and a hole punch or scissors. For re-protecting a disk side, one would simply place a piece of opaque tape over the notch or hole in question. These "flippy disk procedures" were followed by owners of practically every home-computer single sided disk drives. Proper disk labels became quite important for such users. Flippies were eventually adopted by some manufacturers, with a few programs being sold in this medium (they were also widely used for software distribution on systems that could be used with both 40 track and 80 track drives but lacked the software to read a 40 track disk in an 80 track drive).

Certain software companies used tracking outside the standard track designations for copy protection. One notable game that used this technique was the popular game Lode Runner, by Brøderbund, which used quarter tracks written on the original disk as a form of copy protection. Because many disk copying programs did not attempt to copy the secret quarter read/write head increment tracks this kind of protection was mostly successful to the average backup program.

There is an urban myth that it is safe to view a solar eclipse through the film of a floppy removed from its case. Despite some anecdotal support, this in fact does not offer any protection.

More on floppy disk formats

Using the disk space efficiently

In general, data is written to floppy disks in a series of sectors, angular blocks of the disk, and in tracks, concentric rings at a constant radius, e.g. the HD format of 3½-inch floppy disks uses 512 bytes per sector, 18 sectors per track, 80 tracks per side and two sides, for a total of 1,474,560 bytes per disk. (Some disk controllers can vary these parameters at the user's request, increasing the amount of storage on the disk, although these formats may not be able to be read on machines with other controllers; e.g. Microsoft applications were often distributed on Distribution Media Format (DMF) disks, a hack that allowed 1.68 MB (1680 kiB) to be stored on a 3½-inch floppy by formatting it with 21 sectors instead of 18, while these disks were still properly recognized by a standard controller.) On the IBM PC and also on the MSX, Atari ST, Amstrad CPC, and most other microcomputer platforms, disks are written using a Constant Angular Velocity (CAV)—Constant Sector Capacity format. This means that the disk spins at a constant speed, and the sectors on the disk all hold the same amount of information on each track regardless of radial location.

However, this is not the most efficient way to use the disk surface, even with available drive electronics. Because the sectors have a constant angular size, the 512 bytes in each sector are packed into a smaller length near the disk's centre than nearer the disk's edge. A better technique would be to increase the number of sectors/track toward the outer edge of the disk, from 18 to 30 for instance, thereby keeping constant the amount of physical disk space used for storing each 512 byte sector (see zone bit recording). Apple implemented this solution in the early Macintosh computers by spinning the disk slower when the head was at the edge while keeping the data rate the same, allowing them to store 400 kB per side, amounting to an extra 160 kB on a double-sided disk. This higher capacity came with a serious disadvantage, however: the format required a special drive mechanism and control circuitry not used by other manufacturers, meaning that Mac disks could not be read on any other computers. Apple eventually gave up on the format and used constant angular velocity with HD floppy disks on their later machines; these drives were still unique to Apple as they still supported the older variable-speed format.

The Commodore 64/128

Commodore started its tradition of special disk formats with the 5¼-inch disk drives accompanying its PET/CBM, VIC-20 and Commodore 64 home computers, the same as the 1540 and 1541 drives used with the later two machines. The standard Commodore Group Code Recording scheme used in 1541 and compatibles employed four different data rates depending upon track position (see zone bit recording). Tracks 1 to 17 had 21 sectors, 18 to 24 had 19, 25 to 30 had 18, and 31 to 35 had 17, for a disk capacity of 170 kB (170.75 KiB). Unique among personal computer architectures, the operating system on the computer itself was unaware of the details of the disk and filesystem; disk operations were handled by Commodore DOS instead, which was implemented as firmware on the disk drive.

Eventually Commodore gave in to disk format standardization, and made its last 5¼-inch drives, the 1570 and 1571, compatible with Modified Frequency Modulation (MFM), to enable the Commodore 128 to work with CP/M disks from several vendors. Equipped with one of these drives, the C128 was able to access both C64 and CP/M disks, as it needed to, as well as MS-DOS disks (using third-party software), which was a crucial feature for some office work.

Commodore also offered its 8-bit machines a 3½-inch 800 kB disk format with its 1581 disk drive, which used only MFM.

The GEOS operating system used a disk format that was largely identical to the Commodore DOS format with a few minor extensions; while generally compatible with standard Commodore disks, certain disk maintenance operations could corrupt the filesystem without proper supervision from the GEOS kernel.

The Atari 8-bit line

The combination of DOS and hardware (810 and 1050 disk drives) for Atari 8-bit floppy usage allowed sectors numbered from 1 to 720. The DOS' 2.0 disk bitmap, however, which provides information on sector allocation, counts from 0 to 719. As a result, sector 720 could not be written to by the DOS. Some companies used a copy protection scheme where "hidden" data was put in sector 720 that could not be copied through the DOS copy option. Later DOS versions (2.5) and DOS systems by third parties (i.e. OSS) accepted (and formatted) disks with up to 960 and 1020 sectors, resulting in 127KB storage capacity per disk side vs. previous 90KB.

The Commodore Amiga

The pictured chip, codenamed Paula, controlled floppy access on all revisions of the Commodore Amiga as one of its many functions.
The pictured chip, codenamed Paula, controlled floppy access on all revisions of the Commodore Amiga as one of its many functions.

The Commodore Amiga computers used an 880 kB format (eleven 512-byte sectors per track) on a 3½-inch floppy. Because the entire track was written at once, inter-sector gaps could be eliminated, saving space. The Amiga floppy controller was much more flexible than the one on the PC: it did not impose arbitrary format restrictions, and foreign formats such as the IBM PC could also be handled (by use of CrossDos, which was included in later versions of Workbench). With the correct filesystem software, an Amiga could theoretically read any arbitrary format on the 3.5-inch floppy, including those recorded at a differential rotation rate. On the PC, however, there is no way to read an Amiga disk without special hardware or a second floppy drive, which is also a crucial reason for an emulator being technically unable to access real Amiga disks inserted in a standard PC floppy disk drive.

Commodore never upgraded the Amiga chip set to support high-density floppies, but sold a custom drive (made by Chinon) that spun at half speed (150 RPM) when a high-density floppy was inserted, enabling the existing floppy controller to be used. This drive was introduced with the launch of the Amiga 3000, although the later Amiga 1200 was only fitted with the standard DD drive. The Amiga HD disks could handle 1760 kB, but using special software programs it could hold even more data. A company named Kolff Computer Supplies also made an external HD floppy drive (KCS Dual HD Drive) available which could handle HD format diskettes on all Amiga computer systems .

Because of storage reasons, the use of emulators and preserving data, many disks were packed into disk-images. Currently popular formats are .ADF ( Amiga Disk File), .DMS ( DiskMasher) and .IPF ( Interchangeable Preservation Format) files. The DiskMasher format is copyright-protected and has problems storing particular sequences of bits due to bugs in the compression algorithm, but was widely used in the pirate and demo scenes. ADF has been around for almost as long as the Amiga itself though it was not initially called by that name. Only with the advent of the Internet and Amiga emulators has it become a popular way of distributing disk images. IPF files were created to allow preservation of commercial games which have copy protection, which is something that ADF and DMS unfortunately cannot do.

The Electron, BBC Micro and Acorn Archimedes

The British company Acorn used non-standard disk formats in their 8-bit BBC Micro and Acorn Electron, and their successor the 32-bit Acorn Archimedes. The original disk implementation for the BBC Micro stored 100 KiB (40 track) or 200 KiB (80 track) per side on 5¼-inch discs in a custom format using the Disc Filing System (DFS).

For their Electron floppy disk add-on added, Acorn picked 3½-inch disks and developed the Advanced Disc Filing System (ADFS). It used double-density recording and added the ability to treat both sides of the disc as a single drive. This offered three formats: S (small) — 160 KiB, 40-track single-sided; M (medium) — 320 KiB, 80-track single-sided; and L (large) — 640 KiB, 80-track double-sided. ADFS provided hierarchical directory structure, rather than the flat model of DFS. ADFS also stored some metadata about each file, notably a load address, an execution address, owner and public privileges and a "lock" bit. Even on the eight-bit machines, load addresses were stored in 32-bit format.

The ADFS format was later adopted into the BBC line upon release of the BBC Master. The BBC Master Compact marked the move to 3½-inch disks, using the same ADFS formats.

The Acorn Archimedes added D format, which increased the number of objects per directory from 44 to 77, and increased the storage space to 800 KiB. The extra space was obtained by using 1024 byte sectors instead of the usual 512 bytes, thus reducing the space needed for inter-sector gaps. As a further enhancement, successive tracks were offset by a sector, giving time for the head to advance to the next track without missing the first sector, thus increasing bulk throughput. The Archimedes used special values in the ADFS load/execute address metadata to store a 12-bit filetype field and a 40-bit timestamp.

RISC OS 2 introduced E format, which retained the same physical layout as D format, but supported file fragmentation and auto-compaction. Post-1991 machines including the A5000 and Risc PC added support for high-density discs with F format, storing 1600 KiB. However, the PC combo IO chips used were unable to format discs with sector skew, losing some performance. ADFS and the PC controllers also support extended-density disks as G format, storing 3200 KiB, but ED drives were never fitted to production machines.

With RISC OS 3, the Archimedes could also read and write disk formats from other machines, for example the Atari ST and the IBM PC. With third party software it could even read the BBC Micro's original single density 5¼-inch DFS disks. The Amiga's disks could not be read as they used unusual sector gap markers.

The Acorn filesystem design was interesting because all ADFS-based storage devices connected to a module called FileCore which provided almost all the features required to implement an ADFS-compatible filesystem. Because of this modular design, it was easy in RISC OS 3 to add support for so-called image filing systems. These were used to implement completely transparent support for IBM PC format floppy disks, including the slightly different Atari ST format. Computer Concepts released a package that implemented an image filing system to allow access to high density Macintosh format disks.

4-inch floppy diskettes

In the mid-80s, IBM developed a 4-inch floppy diskette, the Demidiskette. This program was driven by aggressive cost goals, but missed the pulse of the industry. The prospective users, both inside and outside IBM, preferred standardization to what by release time were small cost reductions, and were unwilling to retool packaging, interface chips and applications for a proprietary design. The product never appeared in the light of day, and IBM wrote off several hundred million dollars of development and manufacturing facility.


IBM developed, and several companies copied, an autoloader mechanism that could load a stack of floppies one at a time into a drive unit. These were very bulky systems, and suffered from media hangups and chew-ups more than standard drives, but they were a partial answer to replication and large removable storage needs. The smaller 5¼- and 3½-inch floppy made this a much easier technology to perfect.

Floppy mass storage

A number of companies, including IBM and Burroughs, experimented with using large numbers of unenclosed disks to create massive amounts of storage. The Burroughs system used a stack of 256 12-inch disks, spinning at high speed. The disk to be accessed was selected by using air jets to part the stack, and then a pair of heads flew over the surface as in any standard hard disk drive. This approach in some ways anticipated the Bernoulli disk technology implemented in the Iomega Bernoulli Box, but head crashes or air failures were spectacularly messy. The program did not reach production.

2-inch floppy disks

2-inch Video Floppy Disk from Canon.
2-inch Video Floppy Disk from Canon.

A small floppy disk was also used in the late 1980s to store video information for still video cameras such as the Sony Mavica (not to be confused with current Digital Mavica models) and the Ion and Xapshot cameras from Canon. It was officially referred to as a Video Floppy (or VF for short).

VF was not a digital data format; each track on the disk stored one video field in the analog interlaced composite video format in either the North American NTSC or European PAL standard. This yielded a capacity of 25 images per disk in frame mode and 50 in field mode.

The same media were used digitally formatted - 720 kB double-sided, double-density - in the Zenith Minisport laptop computer circa 1989. Although the media exhibited nearly identical performance to the 3½-inch disks of the time, they were not successful. This was due in part to the scarcity of other devices using this drive making it impractical for software transfer, and high media cost which was much more than 3½-inch and 5¼-inch disks of the time.

Ultimate capacity and speed

Floppy disk drive and floppy media manufacturers specify an unformatted capacity, which is, for example, 2.0 MB for a standard 3½-inch HD floppy. It is implied that this data capacity should not be exceeded since exceeding such limitations will most likely degrade the design margins of the floppy system and could result in performance problems such as inability to interchange or even loss of data.

User available data capacity is a function of the particular disk format used which in turn is determined by the FDD controller manufacturer and the settings applied to its controller. The differences between formats can result in user data capacities ranging from 720 KiB (.737 MB) or less up to 1760 KiB (1.80 MB) or even more on a "standard" 3½-inch HD floppy. The highest capacity techniques require much tighter matching of drive head geometry between drives; this is not always possible and cannot be relied upon. The LS-240 drive supports a (rarely used) 32 MB capacity on standard 3½-inch HD floppies—it is, however, a write-once technique, and cannot be used in a read/write/read mode. All the data must be read off, changed as needed and rewritten to the disk. The format also requires an LS-240 drive to read.

Some special hardware/software tools, such as the CatWeasel floppy disk controller and software, which claim up to 2.23 MB of formatted capacity on a HD floppy. Such formats are not standard, hard to read in other drives and possibly even later with the same drive, and are probably not very reliable. It is probably true that floppy disks can surely hold an extra 10–20% formatted capacity versus their "nominal" values, but at the expense of reliability or hardware complexity.

DSED 3½" FDDs introduced by Toshiba in 1987 and adopted by IBM on the PS/2 in 1994 operate at twice the data rate and have twice the capacity of DSHD 3½" FDDs. The only serious attempt to speed up a 3.5” floppy drive beyond 2X was a 10X floppy drive. X10 accelerated floppy drive. It used a combo of RAM and 4X spindle speed to read a floppy in less than 6 seconds vs. the over 1 min time it normally takes.

3½-inch HD floppy drives typically have a transfer rate of 1000 kilobits/second (minus overhead such as error correction and file handling). (For comparison a 1X CD transfers at 1200 kilobits/second (maximum), and a 1X DVD transfers at approximately 11,000 kilobits/second.) While the floppy's data rate cannot be easily changed, overall performance can be improved by optimizing drive access times, shortening some BIOS introduced delays (especially on the IBM PC and compatible platforms), and by changing the sector:shift parameter of a disk, which is, roughly, the numbers of sectors that are skipped by the drive's head when moving to the next track.

This happens because sectors are not typically written exactly in a sequential manner but are scattered around the disk, which introduces yet another delay. Older machines and controllers may take advantage of these delays to cope with the data flow from the disk without having to actually stop.


One of the chief usability problems of the floppy disk is its vulnerability. Even inside a closed plastic housing, the disk medium is still highly sensitive to dust, condensation and temperature extremes. As with any magnetic storage, it is also vulnerable to magnetic fields. Blank floppies have usually been distributed with an extensive set of warnings, cautioning the user not to expose it to conditions which can endanger it.

Users damaging floppy disks (or their contents) were once a staple of "stupid user" folklore among computer technicians. These stories poked fun at users who stapled floppies to papers, made faxes or photocopies of them when asked to "copy a disk", or stored floppies by holding them with a magnet to a file cabinet. Also, these same users were, conversely, often the victims of technicians' hoaxes. Stories of them being carried on Subway/Underground systems wrapped in tin-foil to protect them from the magnetic fields of the electric power supply were common (for an explanation of why this is plausible, see Faraday cage). The flexible 5¼-inch disk could also (folklorically) be abused by rolling it into a typewriter to type a label, or by removing the disk medium from the plastic enclosure used to store it safely.

On the other hand, the 3½-inch floppy has also been lauded for its mechanical usability by HCI expert Donald Norman:

A simple example of a good design is the 3½-inch magnetic diskette for computers, a small circle of "floppy" magnetic material encased in hard plastic. Earlier types of floppy disks did not have this plastic case, which protects the magnetic material from abuse and damage. A sliding metal cover protects the delicate magnetic surface when the diskette is not in use and automatically opens when the diskette is inserted into the computer. The diskette has a square shape: there are apparently eight possible ways to insert it into the machine, only one of which is correct. What happens if I do it wrong? I try inserting the disk sideways. Ah, the designer thought of that. A little study shows that the case really isn't square: it's rectangular, so you can't insert a longer side. I try backward. The diskette goes in only part of the way. Small protrusions, indentations, and cutouts, prevent the diskette from being inserted backward or upside down: of the eight ways one might try to insert the diskette, only one is correct, and only that one will fit. An excellent design.

The floppy as a metaphor

Screenshot of the toolbar in Openoffice.org, highlighting the Save icon, a floppy disk.
Screenshot of the toolbar in Openoffice.org, highlighting the Save icon, a floppy disk.

For more than two decades, the floppy disk was the primary external writable storage device used. Also, in a non-network environment, floppies have been the primary means of transferring data between computers (sometimes jokingly referred to as Sneakernet or Frisbeenet). Floppy disks are also, unlike hard disks, handled and seen; even a novice user can identify a floppy disk. Because of all these factors, the image of the floppy disk has become a metaphor for saving data, and the floppy disk symbol is often seen in programs on buttons and other user interface elements related to saving files.

Retrieved from " http://en.wikipedia.org/wiki/Floppy_disk"
The 2008 Wikipedia for Schools has a sponsor: SOS Children , and consists of a hand selection from the English Wikipedia articles with only minor deletions (see www.wikipedia.org for details of authors and sources). The articles are available under the GNU Free Documentation License. See also our Disclaimer.